How large is the VIC9060F working area?
It is listed as 900*600mm. Compare the full blank and intended layout in both directions before selecting the model.
Laser Cutting Machine
VIC9060F — VIC-F Laser Cutting Machine
VIC9060F has a 900*600mm working area in the VIC-F CO2 laser cutting series. The family is described with a fully enclosed cutting area and a structure containing a CO2 head and tube, linear guides, stepper motors and belt drive. The table lists an 80-600W laser power range.
Compare this rectangle with the smaller VIC6040F and larger VIC1390F using the same proposed blank. Keep the intended part layout alongside those dimensions. A size shortlist is useful only when the quotation also addresses the worktable choice, equipment access and processing requirements for the particular material and drawing.
Technical specifications
| Specification | VIC9060F |
|---|---|
| Working Area | 900*600mm |
| Laser Type | CO2 Laser |
| Working Table | Knife Table or Honeycomb Table |
| Laser Power | 80-600W |
| Power Supply | 220V/50HZ, 110V/60HZ |
| Min Line Width | ≤0.15mm |
| Position Accuracy | 0.01mm |
| Repetition Accuracy | 0.02mm |
| Cutting Speed | 150mm/s |
| Control System | Ruida (USB Interface) |
| Graphic Format Support | PLT, DXF, BMP, JPG, AI, etc |
Configuration options vary by model. Confirm the final specification, selected components and operating requirements with your quotation.
Other models in this series
VIC9060F working area and equipment structure
The VIC9060F working area is 900*600mm. VIC6040F lists 600*400mm and VIC1390F lists 1300*900mm. Check both dimensions against the complete layout instead of comparing only the longest edge. The table does not give the enclosure opening or overall equipment dimensions, which require separate confirmation for the offered machine.
A fully enclosed cutting area is explicitly described for the family. If the way the material is introduced or removed is important to your operation, explain the requirement and ask for the proposed arrangement. The enclosure label alone does not establish a particular access method, loading clearance or certified level of protection.
Knife and honeycomb worktables are listed as alternatives; the configuration description identifies aluminum blades for the knife-table arrangement. Ask for the proposed support surface to be named in the quotation. Keep that selection linked to the actual blank and part outlines rather than assuming a table choice from a general product image.
Planning work with VIC9060F enclosed cutting area
An application discussion should identify the material grade, thickness and required cut result. Provide the finished dimensions and any visual reference for the edge or surface. The published area and structural description do not supply a processing recipe or prove that a particular material and drawing combination will meet your requirements.
Suppose a buyer is deciding whether regular work and an occasional larger blank can share one equipment choice. Submit representative drawings for both and identify which job drives the selection. Ask for the proposed setup to address each requirement explicitly, including the relevant table and access arrangement within the enclosed cutting area.
VIC9060F configuration
Ruida control with USB is listed, with PLT, DXF, BMP, JPG and AI among supported graphic formats. Give each submitted drawing its revision, scale and units. Where several layouts are under discussion, label them separately so that a configuration response for one arrangement is not mistaken for approval of every alternative.
Power supply entries are 220V/50HZ and 110V/60HZ. Request the version matching your installation location together with the selected laser power. The table's 80-600W range does not define which rating appears in an individual quotation, and the two electrical entries do not state automatic switching between supplies.
The table gives Position Accuracy of 0.01mm, Repetition Accuracy of 0.02mm and Cutting Speed of 150mm/s. Keep these labels separate from the finished-part limits and job time you require. A clear request connects the selected model, material, drawing, table choice and expected result without deriving a production promise from the speed entry.
Product questions
What are the neighbouring area choices?
VIC6040F lists 600*400mm and VIC1390F lists 1300*900mm. Use the same layout orientation when comparing the three rectangles.
Does the enclosed design specify how material is loaded?
The admitted description establishes an enclosed cutting area, but does not define a loading method or clearance. Request those details for the proposed equipment.
Does the table entry include both surface types?
Knife or honeycomb alternatives are listed. Confirm the selected table; the aluminum-blade description relates to the knife arrangement.
How should regular and occasional jobs be presented?
Give each its drawing, material, thickness, blank dimensions and required result. Identify which job motivates the size choice and which setup questions remain open.
Related equipment and information
Ready to discuss VIC9060F?
Share your material, dimensions and process. Start a conversation about the right configuration.