What is the published area for VIE4015?
The VIE4015 Cutting Area entry is 4000*1500mm. It is different from the overall equipment dimensions needed for site planning.
Sheet Laser Cutting Machine
VIE4015 — VIE Laser Cutting Machine
VIE4015 specifications identify the 4000*1500mm model in the VIE sheet laser cutting series. It retains the 1500mm area dimension of VIE3015 while providing a 4000mm entry in place of 3000mm. The published laser power range is 1500-20000W, and the table lists component alternatives to resolve in the quotation.
A buyer moving between sheet formats can use this model comparison to keep the size requirement clear. Name the format currently required and any other format under consideration. Then attach the drawings and configuration questions to that choice, so a change of model has an identifiable reason.
Technical specifications
| Specification | VIE4015 |
|---|---|
| Cutting Area | 4000*1500mm |
| Laser Head | Raytools, WSX, BOCI, Osprey |
| Laser Power | 1500-20000W |
| Laser Generator | Raycus, MAX, IPG |
| Control System | CypCut, Weihong |
| Servo Motor And Driver | Fuji, Delta, Yaskawa |
| Guide Rails | Taiwan Linear Rails |
| Reducer | Japan Shinbo, France Mortori |
| Max. Acceleration | 1.3G |
| Z Axis Travel | 300mm |
| Positioning Accuracy | 0.05mm |
| Repositioning Accuracy | 0.03mm |
Configuration options vary by model. Confirm the final specification, selected components and operating requirements with your quotation.
Other models in this series
VIE4015 cutting area and the model shortlist
The VIE4015 cutting area can be compared with VIE6025 at 6000*2500mm when both dimensions are part of the decision. For a comparison that keeps the 1500mm dimension unchanged, VIE6015 lists 6000*1500mm. These entries describe cutting areas; they do not supply an installation footprint.
The model's maximum acceleration is listed at 1.3G, with Z axis travel of 300mm. Keep these values attached to VIE4015 in a specification comparison. The 1.4G entry shown for VIE3015 is a different model's value, and neither acceleration figure states a processing time for the intended work.
Positioning Accuracy is 0.05mm and Repositioning Accuracy is 0.03mm. Use the original field names in an equipment comparison, and use the drawing's own dimensional requirements for the component discussion. Treating those two kinds of information separately gives the supplier a clearer question to answer.
Revision control for a VIE4015 fiber laser cutting machine inquiry
A VIE4015 fiber laser cutting machine brief should make drawing changes easy to follow. State the current revision, material grade, thickness and stock dimensions for each representative part. If a new revision changes the overall outline, flag that change rather than assuming it is evident from the file name.
If the intended workload contains both repeat orders and occasional parts, distinguish them. Give the quantities and drawing references for each group. That helps explain why the 4000*1500mm model is on your shortlist without turning the published area into an unsupported promise about output or job suitability.
During the quotation discussion, keep open questions in a separate list: proposed power, selected components, requirements needing review and installation information for the destination. Once an answer changes the proposal, identify the corresponding revision so the commercial and technical descriptions remain aligned.
VIE4015 configuration requirements
VIE4015 configuration alternatives include Raytools, WSX, BOCI and Osprey heads and Raycus, MAX and IPG generators. Select a power rating and ask for the proposed head and source to be stated with it. A range and a list of brands are starting information, not the description of a fully defined offer.
The controls listed are CypCut and Weihong. Fuji, Delta and Yaskawa appear for the servo motor and driver. Where your team has a preferred component, include that preference in the inquiry and obtain the proposed selection in writing rather than assuming it from a general series description.
The guide rail row states Taiwan Linear Rails, and the reducer row lists Japan Shinbo and France Mortori. Use the VIE series page to check other areas and the contact page to discuss the complete proposal. Keep the chosen components beside VIE4015 throughout that exchange.
Product questions
How is VIE6025 different in the area table?
VIE6025 lists 6000*2500mm, changing both area dimensions from the VIE4015 entry of 4000*1500mm.
What acceleration should appear beside VIE4015?
The correct maximum acceleration entry is 1.3G. The VIE3015 entry of 1.4G should not be transferred to this model.
Which configuration details need a definite selection?
Specify the power, laser head, generator, controls and drive components in the proposed offer. The published brand alternatives are not simultaneous inclusions.
How should a revised drawing be submitted?
Identify the new revision and describe the changed requirement, keeping the material, thickness and stock format with it. Ask whether the proposal needs a corresponding revision.
Related equipment and information
Compare VIE Laser Cutting Machine models
Ready to discuss VIE4015?
Share your material, dimensions and process. Start a conversation about the right configuration.